FMEA Template and Practical Example

In this article, we provide an FMEA Template, a Practical FMEA Example, and a training video showing you how to create an FMEA in excel. This video runs 4:45 minutes.

Practitioners of Lean Manufacturing and Six Sigma can use this tool to identify potential problems and their impact on a process. Before you continue reading, be warned: this post is long and is more of a “how to do fmea” than it is entertaining or fun. In that spirit, if you are learning how to apply an FMEA, then read on.

Problems and defects are expensive. Customers place high expectations on manufacturers and service providers to deliver quality and reliability.

Often, faults in products and services are detected through extensive testing and predictive modeling in the later stages of development. However, finding a problem at this point in the cycle can add significant cost and delays to schedules. The challenge is to design in quality and reliability at the beginning of the process and ensure that defects never arise in the first place. One way that Lean Six Sigma practitioners can achieve this is to use failure mode and effects analysis (FMEA), a tool for identifying potential problems and their impact.

FMEA: The Basics

FMEA is a qualitative and systematic tool, usually created within a spreadsheet, to help practitioners anticipate what might go wrong with a product or process. In addition to identifying how a product or process might fail and the effects of that failure, FMEA also helps find the possible causes of failures and the likelihood of failures being detected before occurrence.

Used across many industries, FMEA is one of the best ways of analyzing potential reliability problems early in the development cycle, making it easier for manufacturers to take quick action and mitigate failure. The ability to anticipate issues early allows practitioners to design out failures and design in reliable, safe and customer-pleasing features.

Now, let’s go into the details of the FMEA for itself and how to conduct an FMEA team exercise. In what follows, we’ll show an example, then watch the premium member-only video.

Finding Failure Modes

One of the first steps to take when completing an FMEA is to determine the participants. The right people with the right experience, such as process owners and designers, should be involved in order to catch potential failure modes. Practitioners also should consider inviting customers and suppliers to gather alternative viewpoints.

Once the participants are together, the brainstorming can begin. When completing an FMEA, it’s important to remember Murphy’s Law: Anything that can go wrong, will go wrong. Participants need to identify all the components, systems, processes and functions that could potentially fail to meet the required level of quality or reliability. The team should not only be able to describe the effects of the failure, but also the possible causes.

The sample shown in Figure 1 can be used as an example when learning how the FMEA works. The team in this case is analyzing the tire component of a car.

Figure 1: FMEA Template for Car Tire

Criteria for FMEA Analysis

An FMEA uses three criteria to assess a problem: 1) the severity of the effect on the customer, 2) how frequently the problem is likely to occur and 3) how easily the problem can be detected. Participants must set and agree on a ranking between 1 and 10 (1 = low, 10 = high) for the severity, occurrence and detection level for each of the failure modes. Although FMEA is a qualitative process, it is important to use data (if available) to qualify the decisions the team makes regarding these ratings. A further explanation of the ratings is shown in Table 1.

Table 1: Severity, Occurrence and Detection Ratings

After ranking the severity, occurrence and detection levels for each failure mode, the team will be able to calculate a risk priority number (RPN). The formula for the RPN is:

RPN = severity x occurrence x detection

In the FMEA in Figure 1, for example, a flat tire severely affects the customer driving the car (rating of 10), but has a low level of occurrence (2) and can be detected fairly easily (3). Therefore, the RPN for this failure mode is 10 x 2 x 3 = 60.

FMEA: Setting Priorities

Once all the failure modes have been assessed, the team should adjust the FMEA to list failures in descending RPN order. This highlights the areas where corrective actions can be focused. If resources are limited, practitioners must set priorities on the biggest problems first.

There is no definitive RPN threshold to decide which areas should receive the most attention; this depends on many factors, including industry standards, legal or safety requirements, and quality control. However, a starting point for prioritization is to apply the Pareto rule: typically, 80 percent of issues are caused by 20 percent of the potential problems. As a rule of thumb, teams can focus their attention initially on the failures with the top 20 percent of the highest RPN scores.

FMEA: Making Corrective Actions

When the priorities have been agreed upon, one of the team’s last steps is to generate appropriate corrective actions for reducing the occurrence of failure modes, or at least for improving their detection. The FMEA leader should assign responsibility for these actions and set target completion dates.

Once corrective actions have been completed, the team should meet again to reassess and re-score the severity, probability of occurrence and likelihood of detection for the top failure modes. This will enable them to determine the effectiveness of the corrective actions taken. These assessments may be helpful in case the team decides that it needs to enact new corrective actions.

The FMEA is a valuable tool that can be used to realize a number of benefits, including improved reliability of products and services, prevention of costly late design changes, and increased customer satisfaction.